Famco Chimney Cap & Crown Nationwide

Famco Chimney Cap & Crown in Brooklyn: What to Know First

Famco chimney cap and crown work in Brooklyn runs $340 to $780 for most cap replacements and $225 to $460 for crown repair, and we typically finish in one visit. We’re an independent Famco service provider, not a factory-authorized shop, which means we fix what’s actually wrong instead of pushing a full replacement when the old part has years left. If you’ve got a Famco cap that’s pulling away from the crown or a crown that’s shedding concrete onto your roof, call (516) 289-9316 and we’ll give you a straight answer on whether it’s a repair or a replacement.

Call (516) 289-9316

This page is for Brooklyn homeowners who already own Famco equipment and want someone who knows how that brand behaves in this climate. Not a generic cap-and-crown writeup with the name Famco pasted in. Real failure patterns, real prices, and what we do differently on these specific jobs.

How Famco Products Fail - and How We Fix Them

Famco builds solid caps and the rest of the industry knows it. But every brand has its weak spots, and in Brooklyn’s weather, those weak spots show up faster than the manufacturer’s brochure would suggest. Here’s what we see most often, by model line.

• Rust-through at the mesh seam on the Famco TC Series. The TC series uses galvanized mesh with a crimped edge, and in Brooklyn, the seam where the mesh meets the cap body takes the brunt of nor’easter wind-driven rain. The galvanization thins at that crimp line over eight to ten years, then rust blooms and the mesh starts shedding brittle strands. We replace the mesh with stainless where practical, which Famco’s own replacement part won’t offer for older TC units.
• Base-flange warping on the Famco LC Series. The LC line’s stamped base is thinner than the cap body, and on Brooklyn row houses with clay-tile flues, the thermal cycling between a hot flue and freezing rooftop air warps that flange just enough to break the seal. Water creeps under, runs down the outside of the tile, and freezes in the crown. You won’t see the leak from the roof. You’ll see it three winters later when the crown face starts spalling. We re-flatten and re-seal the flange rather than condemning a cap that’s otherwise fine.
• Screen clogging you can actually feel from the fireplace side. This is a Famco issue across most lines: the screen pitch is fine enough to stop embers, but in Brooklyn’s leaf-heavy fall and the soot load from older brownstone boilers, it loads up fast. Draft gets sluggish, the fireplace pushes smoke back into the room. A cap that looks fine from the ground is actually choked. We clean, and if it recurs a second season, we’ll tell you honestly whether a wider-mesh aftermarket screen is worth doing rather than selling you a third cleaning.
• Crown cracks at the corners on almost every Famco setup installed with a full-size chase cover. The concrete crowns under older Famco chase caps shrink as they cure, and the corners are where the stress concentrates. We see this constantly across Carroll Gardens and Park Slope roofs. A hairline crack at the corner is manageable in year one. By year three, it’s a water channel into the chase. We repair with a flexible crown sealant bred for freeze-thaw cycles, not the rigid patch that cracks again next February.
• Neoprene extrusion gaskets drying out on Famco TLC multi-flue caps. TLC units use a gasket between the cap frame and the crown surface, and after six or seven Brooklyn winters, that gasket turns brittle and falls apart in sections. The cap starts lifting on one side, wind gets under it, and you get a rattle that sounds like a raccoon but isn’t. We re-gasket with a higher-durometer aftermarket material that outlasts what Famco ships.

Our Famco Chimney Cap & Crown Process

Every Famco job follows the same path, whether it’s a simple cap replacement in Bay Ridge or a full crown rebuild on a Flatbush brownstone. No surprises, no number changing when the ladder goes up.

1. 1
   You call, a person answers. We talk through what you’re seeing from the ground. If you’ve got photos, even better. We’ll give you a ballpark before we ever set foot on your roof, and we’ll tell you if we don’t think you need us yet.
2. 2
   Roof inspection and camera work. We get eyes on the actual Famco cap, the crown, and the top section of flue. We run a camera down if there’s any question about what’s happening inside where you can’t see.
3. 3
   Plain-English verdict. We show you the footage and explain what’s failing, what can wait, and what can’t. If it doesn’t need doing, Wendell will tell you that too. If it does, the price is set before a single tool comes off the truck.
4. 4
   Parts decision, right in front of you. Some Famco parts are worth buying OEM. Some are better with a quality aftermarket equivalent that won’t gouge you. We walk that trade-off honestly, because you’re the one who lives with it.
5. 5
   The work, done that day. Cap replacement, crown repair, crown coating, whatever the job turned out to be. We clean up the roof, haul the bad parts down, and leave the area cleaner than we found it.
6. 6
   Test and the 90-Day Done Right Promise in writing. We check draft and water seal before we leave. Then you get the promise stamped on the invoice: if it isn’t right, one call brings us back, no charge.

What Famco Chimney Cap & Crown Costs in Brooklyn

Here’s what you’re looking at for the common Famco scenarios in this market. These aren’t national averages. They’re what we see on Brooklyn rooftops, where access can be tight and the weather does more damage.

• Famco TC-Series cap replacement (single flue): $340-$520 installed, depending on roof access and flue size.
• Famco LC-Series cap replacement: $410-$630 installed. The flange work takes more time.
• Famco TLC multi-flue cap (2-3 flues): $580-$780 installed. Custom sizing pushes it higher.
• Crown repair (minor cracking, no rebuild): $225-$340.
• Crown rebuild (full removal and re-pour): $620-$1,200 depending on crown size and chase access.
• Crown coating (sealant + waterproofing, sound crown): $195-$310.

What moves the price: roof height and access. A flat roof in Williamsburg is faster than a steep slate job in Park Slope. Flue count matters on multi-flue work. And the condition of the existing crown drives everything. Call (516) 289-9316 and we’ll give you an exact number before you commit to anything. Estimates are free.

Why Brooklyn Homeowners Call Top Hat Chimney for Famco Work

We’ve been climbing Brooklyn rooftops since 1999, and Wendell Pike has put his name on this work for over two decades. That matters more than any brand affiliation. When you call, a live person answers, and that person may well be Wendell himself. When someone shows up, they’re background-checked and wearing a uniform, and they’ll give you a real arrival window and call if it slips. The quote on the phone is the price on the invoice. No bait and switch, no vague “we’ll see once we get up there.” Every Famco cap and crown job is backed by our 90-Day Done Right Promise in writing. And if we can’t source the right Famco part quickly, we carry or can get lines from DuraFlex, HeatShield, and Gelco, so you’re never stuck waiting on a backorder.

FAQs